Dầu nhớt bán tổng hợp chất lượng cao, bảo vệ hoàn hảo với công nghệ Technosynthese® được khuyến nghị dành cho các dòng xe CHRYSLER, GM, MERCEDES và VAG (Volkswagen, Audi, Skoda và Seat). Sản phẩm được thiết kế đặc biệt dành cho xe hơi đời mới, động cơ xăng và dầu diesel công suất lớn, nạp khí tự nhiên hoặc turbo tăng áp, phun nhiên liệu trực tiếp hoặc gián tiếp, các động cơ theo tiêu chuẩn Euro 4,5 hoặc 6, yêu cầu dầu nhớt đáp ứng tiêu chuẩn ACEA C3 có độ nhớt HTHS cao (> 3.5 mPa.s) và “SAPS trung bình” (Sulfated Ash ≤ 0.8%, Phosphorus 0.07 ≤ x ≤ 0.09% và Sulfur ≤ 0.3%) . Tương thích với bộ chuyển đổi khí thải xúc tác (CAT) và bộ lọc hạt diesel (DPF). Tham khảo hướng dẫn sử dụng của nhà sản xuất trước khi sử dụng.

Engines compliant with Euro 4, 5 and 6 emission regulations are fitted with sensitive exhaust gas after treatment systems. Indeed, Sulfur and Phosphorus inhibit catalytic converter operation leading to inefficient exhaust gas treatment. Also, Sulfated Ashes clog DPFs leading to shorten regenerating cycles, quick oil aging, higher fuel consumption and engine power loss.

The ACEA C3 standard requires from the lubricant significant oil film resistance and low emission performance during use in powerful engines.

MOTUL 6100 SYN-clean 5W-30 features Technosynthese^® synthetic base stocks coupled with specific friction modifier molecules and dedicated SAPS levels that generate outstanding oil film resistance, reduce friction in the engine and provide after treatment devices compatibility. MOTUL 6100 SYN-clean 5W-30 brings high lubricating properties such as wear protection and high temperature resistance for better controlled oil consumption. ACEA C3 lubricants can achieve extended drain intervals as managed by the vehicle on-board computer.

Numerous OEMs such as HONDA, KIA / HYUNDAI, MITSUBISHI, NISSAN, SUBARU, SUZUKI, SSANGYONG, TOYOTA… recommend an ACEA C3 lubricant for most of their vehicles, especially Diesels with DPF.

The CHRYSLER MS-11106 performance level requires the engine oil to combine both MB 229.51 and 5W-30 in order to perfectly lubricate some Diesel engines of CHRYSLER and JEEP vehicles.

The MB 229.51 requires among many other severe constrains from the lubricant a reduced content of Sulfated Ash, Phosphorus and Sulphur in order to be compatible with MERCEDES exhaust gas after treatment systems. The specification MB 229.51 applies to some MERCEDES Gasoline engines, and to all MERCEDES Diesel engines, with or without DPF (except for BlueTEC engines with SCR. In this case use a MB 229.52 lubricant such as MOTUL SPECIFIC 229.52 5W-30 or MOTUL 8100 X-CLEAN EFE 5W-30).

In countries with relevant Diesel passenger car market shares e.g. Europe, the GM-OPEL dexos2^® standard is suitable for the whole range of GM-OPEL Diesel engines (including DPF versions) and Gasoline engines from Model Year 2010. Also, GM-OPEL dexos2^® fully supersedes and replaces the previous GM specifications: GM-LL-A-025 (Gasoline) and GM-LL-B-025 (Diesel).

Specifications VW 505 00 and VW 505 01 require high detergent/dispersant power, high oil film resistance and better viscosity increase resistance (due to soot) in order to cover many old Diesel engines and especially Direct Injection Diesel engines with unit pump injector system (fixed oil drain interval, check owner’s manual). Attention, do not use MOTUL 6100 SYN-clean 5W-30 when a VW 504 00 or VW 507 00 lubricant is required, in that case use MOTUL SPECIFIC 504 00 507 00 5W-30, MOTUL SPECIFIC 504 00 507 00 0W-30 or MOTUL 8100 X-CLEAN+ 5W-30.

Drain interval: according to manufacturers’ recommendations and tuned to your own use.
Do not mix with lubricants not ACEA C3 compliant.
Before using, always refer to the owner’s manual or handbook of the vehicle.